# generated by Slic3r 1.2.9 on Mon Dec  7 11:39:22 2015
avoid_crossing_perimeters = 1
bed_shape = 0x0,210x0,210x297,0x297
bed_temperature = 0
before_layer_gcode = ; LAYER [layer_num], HEIGHT [layer_z]
bottom_solid_layers = 8
bridge_acceleration = 1000
bridge_fan_speed = 100
bridge_flow_ratio = 0.95
bridge_speed = 20
brim_width = 0
complete_objects = 0
cooling = 0
default_acceleration = 1000
disable_fan_first_layers = 0
dont_support_bridges = 1
duplicate_distance = 6
end_gcode = ; -- END GCODE --\nM801        ; Custom GCODE to fire end print procedure\n; -- end of END GCODE --
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0.4
external_perimeter_speed = 20
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extruder_offset = 0x0
extrusion_axis = E
extrusion_multiplier = 1
extrusion_width = 0.4
fan_always_on = 1
fan_below_layer_time = 50
filament_colour = #FFFFFF
filament_diameter = 1.75
fill_angle = 45
fill_density = 20%
fill_pattern = rectilinear
first_layer_acceleration = 1000
first_layer_bed_temperature = 0
first_layer_extrusion_width = 0.4
first_layer_height = 0.1
first_layer_speed = 90%
first_layer_temperature = 205
gap_fill_speed = 100
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
infill_acceleration = 2000
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.65
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 10%
infill_speed = 100
interface_shells = 0
layer_gcode = 
layer_height = 0.1
max_fan_speed = 100
max_print_speed = 200
max_volumetric_speed = 0
min_fan_speed = 100
min_print_speed = 15
min_skirt_length = 5
notes = 
nozzle_diameter = 0.4
octoprint_apikey = 
octoprint_host = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 600
perimeter_extruder = 1
perimeter_extrusion_width = 0.4
perimeter_speed = 40
perimeters = 2
post_process = 
pressure_advance = 0
raft_layers = 0
resolution = 0
retract_before_travel = 2
retract_layer_change = 0
retract_length = 2
retract_length_toolchange = 10
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 200
seam_position = nearest
skirt_distance = 6
skirt_height = 1
skirts = 3
slowdown_below_layer_time = 5
small_perimeter_speed = 20
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.4
solid_infill_speed = 80
spiral_vase = 0
standby_temperature_delta = -5
start_gcode = ; -- START GCODE --\nM800        ; Custom GCODE to fire start print procedure\n; -- end of START GCODE --
support_material = 0
support_material_angle = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = pillars
support_material_spacing = 2.5
support_material_speed = 80
support_material_threshold = 0
temperature = 205
thin_walls = 0
threads = 2
toolchange_gcode = 
top_infill_extrusion_width = 0.4
top_solid_infill_speed = 40
top_solid_layers = 8
travel_speed = 200
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
vibration_limit = 0
wipe = 0
xy_size_compensation = 0
z_offset = 0
